Lantronix Server EDS-MD4 Manuel d'utilisateur Page 46
- Page / 98
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EDS-MD User Guide 46
7: Network Settings
The Network Settings show the status of the Ethernet interface/link and let you configure the
settings on the device. Interface settings are related to the configuration of the IP and related
protocols. Link settings are related to the physical link connection, which carries the IP traffic.
The EDS-MD4, EDS-MD8 and EDS-MD16 contains one network interface. The Ethernet interface
is also called interface 1 or eth0.
Notes:
Some settings require a reboot to take effect. These settings are noted below.
Wait a minimum of 5 seconds after rebooting the unit before attempting to make any
subsequent connections.
The blue text in the XML command strings of this chapter are to be replaced with a
user-specified name.
Network Interface Settings
Table 7-1 shows the network interface settings that can be configured.
Table 7-1 Network Interface Settings
Network Interface
Settings
Description
BOOTP Client Select to turn On or Off. At boot up, after the physical link is up, the EDS-MD
will attempt to obtain IP settings from a BOOTP server.
Note: Overrides the configured IP address/mask, gateway, hostname, and
domain. When DHCP is Enabled, the system automatically uses DHCP,
regardless of whether BOOTP is Enabled. Changing this value requires you to
reboot the device.
DHCP Client Select to turn On or Off. At boot up, after the physical link is up, the EDS-MD
will attempt to obtain IP settings from a DHCP server and will periodically renew
these settings with the server.
Note: Overrides BOOTP, the configured IP address/mask, gateway,
hostname, and domain. Changing this value requires you to reboot the device.
Note: Within WebManager, click Renew to renew the DHCP lease.
IP Address Enter the static IP address to use for the interface. You may enter it alone or in
CIDR format.
Note: This setting will be used if Static IP is active (both DHCP and BOOTP
are Disabled). Changing this value requires you to reboot the device. When
DHCP or BOOTP is enabled, the EDS-MD tries to obtain an IP address from a
DHCP or BOOTP server. If it cannot, the EDS-MD generates and uses an Auto
IP address in the range of 169.254.xxx.xxx, with a network mask of
255.255.0.0.
Default Gateway Enter the IP address of the router for this network.
Note: This setting will be used if Static IP is active (both DHCP and BOOTP
are Disabled).
- User Guide 1
- Copyright & Trademark 2
- Warranty 2
- Contacts 2
- Disclaimer 2
- Revision History 2
- Table of Contents 3
- 1: Using This Guide 15 3
- 2: Introduction 20 3
- 4: Using DeviceInstaller 28 4
- 7: Network Settings 46 5
- 9: Services Settings 52 6
- 10: Security Settings 58 7
- 12: Advanced Settings 75 9
- 13: Updating Firmware 81 10
- 14: VIP Settings 82 10
- List of Figures 12
- List of Tables 13
- 1: Using This Guide 15
- Safety Information 16
- Wall Mounting 17
- Port Connections 17
- Equipment Classifications 18
- Cleaning Instructions 18
- Electromagnetic Interference 18
- Additional Documentation 19
- 2: Introduction 20
- Troubleshooting Capabilities 21
- Configuration Methods 21
- Addresses and Port Numbers 21
- Product Information Label 22
- Package Contents 23
- User-Supplied Items 23
- Serial Ports 24
- Ethernet Port 24
- Reset to Default Button 25
- Technical Specification 26
- Installing the EDS-MD 27
- 4: Using DeviceInstaller 28
- EDS-MD User Guide 29 29
- Accessing Web Manager 30
- Device Status Page 31
- Web Manager Page Components 32
- Navigating the Web Manager 33
- EDS-MD User Guide 34 34
- 6: Line and Tunnel Settings 35
- To Configure Line Settings 36
- To View Line Statistics 36
- Tunnel Settings 37
- Packing Mode 38
- Accept Mode 39
- Connect Mode 41
- Disconnect Mode 42
- Modem Emulation 43
- Statistics 44
- To View Tunnel Statistics 44
- 7: Network Settings 46
- Network Link Settings 48
- Terminal Settings 49
- Host Configuration 50
- To Configure Host Settings 51
- 9: Services Settings 52
- FTP Settings 53
- Syslog Settings 53
- HTTP Settings 54
- To Configure HTTP Settings 55
- RSS Settings 56
- To Configure RTC Settings 57
- 10: Security Settings 58
- SSH Client Known Hosts 59
- SSH Server Authorized Users 59
- SSH Client Users 60
- SSL Settings 61
- To Create a New Credential 62
- Certificate Upload Settings 63
- Trusted Authorities 64
- Filesystem Settings 65
- File Modification 66
- File Transfer 66
- IP Network Stack Settings 67
- Query Port 69
- Diagnostics 70
- To Ping a Remote Host 71
- Traceroute 71
- To Perform a Traceroute 71
- To View Memory Usage 72
- Processes 73
- To View Process Information 73
- To View Thread Information 73
- System Settings 74
- 12: Advanced Settings 75
- Basic CLI Settings 76
- Telnet Settings 77
- To Configure Telnet Settings 77
- SSH Settings 77
- XML Settings 78
- XML: Export Status 79
- To Export in XML Format 79
- XML: Import Configuration 80
- 13: Updating Firmware 81
- 14: VIP Settings 82
- Virtual IP (VIP) Counters 83
- 15: Branding the EDS-MD4/8/16 84
- Name Settings Description 85
- Conversion Table 87
- Scientific Calculator 87
- EDS-MD User Guide 88 88
- Appendix C: Compliance 89
- EDS-MD User Guide 91 91
- EDS-MD User Guide 92 92
- Port Pinouts 93
- EDS-MD User Guide 94 94
- EDS-MD User Guide 95 95
- EDS-MD User Guide 96 96
- EDS-MD User Guide 97 97
- EDS-MD User Guide 98 98
Produits connexes et manuels pour Mise en réseau Lantronix Server EDS-MD4
(43 pages)HP SAN Solutions manuels
Manuels d'utilisation et guides de l'utilisateur pour Cartouches d'encre HP SAN Solutions.
Nous fournissons des manuels en pdf 1 HP SAN Solutions à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels