Lantronix Device Server UDS 10 Manuel d'utilisateur Page 38
- Page / 139
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Getting Started
2-10
UDS-10 User Guide
2.4.5 Opening a Configuration Window
1. Click the Manage icon . The Device Management window displays.
Figure 10 - Device Management Window
2. Do one of the following:
Note: To assign Expert settings and Security settings, you must use the Setup Mode window
in a Telnet session.
• To configure the unit via a Web browser, click the Web Configuration icon
.
The Lantronix Web-Manager window displays in your browser. For Web
Configuration, see Web Manager Page on page 3-4.
• To configure the unit via a Telnet session, click the Telnet to Device icon
.
The Setup Mode window displays. For Telnet Configuration, see Using a Telnet
Connection on page 3-10
3. Continue with the appropriate configuration procedure described in the next chapter.
Note: The Get Configuration icon on the Device Management window allows you to save a
configuration locally on your computer as a file. The Set Configuration icon sends a saved
file to the unit.
To Get Configuration information see Get Configuration on page 3-27. To Set
Configuration of a specific device see Set Configuration on page 3-28.
- User Guide 1
- Copyright and Trademark 2
- Disclaimer and Revisions 3
- Declaration of Conformity 4
- Warranty 5
- Sales Offices 6
- Table of Contents 7
- UDS-10 User Guide iii 9
- Contents 10
- UDS-10 User Guide 10
- List of Figures 11
- List of Tables 12
- UDS-10 User Guide vii 13
- 1. Introduction 15
- 1.1 UDS-10 16
- 1.2 UDS-10B 17
- 1.3 UDS-10-IAP Device Server 18
- Introduction 19
- UDS-10 User Guide 1-5 19
- 1.4 Network Protocols 20
- 1.5 Serial Interface 21
- 1.6 RJ-45 Ethernet Interface 21
- 1.7 Ethernet Cable 22
- UDS-10 User Guide 1-9 23
- 1.9 LEDs 24
- 1.10 Dimensions 25
- 1.12 Software Support 25
- 1.13 Power Requirements 26
- 1.14 Reset Switch 26
- Table 3 - Technical Specs 27
- 2. Getting Started 29
- 2.1.3 Port Number 30
- Ethernet 30
- 2.3.1 DHCP 32
- 2.3.2 AutoIP 32
- 2.4 DeviceInstaller 33
- Getting Started 34
- 2.4.3 Test the IP Address 35
- UDS-10 User Guide 2-9 37
- 2.5 ARP and Telnet 39
- 2.6 Serial Port Login 40
- 3. Configuring the Unit 41
- 3.2 Using DeviceInstaller 42
- Configure 43
- UDS-10 User Guide 3-3 43
- 3.3 Web Manager Page 44
- 3.3.1 Unit Configuration 45
- 3.3.2 Server Properties 46
- 3.3.3 Port Properties 47
- 3.3.4 Technical Support 49
- 3.3.5 Update Settings 49
- UDS-10 User Guide 3-11 51
- 3.5.5 DHCP Naming 54
- UDS-10 User Guide 56
- 3.6.3 Flow 57
- 3.6.4 Port Number 57
- 3.6.5 Connect Mode 58
- UDS-10 User Guide 3-19 59
- 3.6.10 Pack Control 63
- 3.6.12 Send Characters 64
- 3.6.13 Telnet Terminal Type 64
- 3.7 Expert Settings 65
- 3.8 Security Settings 65
- 3.9 Factory Defaults 66
- 3.11 Get Configuration 67
- 3.12 Set Configuration 68
- 4.1 Protocol Firmware 69
- 4.2.1 Via DeviceInstaller 70
- Firmware 71
- UDS-10 User Guide 4-3 71
- 4.2.2 Via TFTP 72
- 4.2.3 Via Another Unit 73
- SF x.x.x.x 73
- 02049 lines loaded 74
- 4.2.4 Via the Serial Port 74
- *** NodeSet 2.0 *** 74
- 5. DeviceComm Manager 75
- UDS-10 User Guide 5-3 77
- 6. Troubleshooting 79
- Troubleshooting 80
- UDS-10 User Guide 6-3 81
- UDS-10 User Guide 6-5 83
- 7. Monitor Mode 85
- 8.1 UDP Datagrams 87
- UDS-10 User Guide 8-3 89
- 8.2.2 Sending a Setup Record 90
- 8.2.3 The Intel Hex Format 91
- 00000001FF 91
- 01002000805F 91
- 0300300002337A1E 92
- 8.3 Setup Records 93
- 8.3.1 Channel Parameters 94
- 8.3.3 Baud Rate 96
- 8.3.4 Flow Control 96
- 8.3.5 Connect Mode 97
- UDS-10 User Guide 8-13 99
- 8.4 IP Addresses 100
- 8.4.3 Host Portion 101
- 8.4.4 Network Address 101
- 192.168.0.0 101
- 8.4.5 Broadcast Address 101
- 192.168.0.255 101
- 8.4.7 Network RFCs 102
- 9. Binary to Hex Conversion 103
- 9.1 Connect Mode Options 104
- Binary to Hex 105
- UDS-10 User Guide 9-3 105
- Accept Incoming 106
- Connections 106
- Response Hex 106
- 9.2 Disconnect Mode Options 107
- UDS-10 User Guide 9-7 109
- 9.4 Interface Mode Options 115
- 9.5 Pack Control Options 116
- UDS-10 User Guide 9-15 117
- 10. IP Addresses 119
- 10.4 Network Address 120
- 10.5 Broadcast Address 120
- 10.6 IP Netmask 120
- 10.8 Network RFCs 121
- 11. Glossary of Terms 123
Produits connexes et manuels pour Mise en réseau Lantronix Device Server UDS 10
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels