Lantronix Switch XSENSO 2100 Manuel d'utilisateur Page 39
- Page / 125
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5: Installation of xSenso 21R2
xSenso User Guide 39
Figure 5-7 xSenso Bottom/Back Panel View
Installing the xSenso
Be sure to place or mount the device securely on a flat horizontal or vertical surface. The device
comes with mounting brackets for mounting the device vertically, for example on a wall. If using
AC power, avoid outlets controlled by a wall switch.
Observe the following guidelines when connecting the analog input and output devices:
It is recommended to use twisted-pair wires to connect analog sensors and xSenso. If EMC is
a concern, shielded wires and/or ferrite bead may be used to improve signal integrity in noisy
environment.
Connect your RJ-45 Ethernet cable to the RJ-45 port of the unit.
The xSenso supports a power range of 9 to 30 VDC. You can power up the device with barrel-
power connector and/or the 3 pin terminal connector for backup power supply.
Note: As soon as you plug the device into power, the device/sensors powers up
automatically, the self-test begins, and LEDs would indicate the device's status
Perform the following steps to install your device:
1. Connect analog devices to the analog input and relay output ports.
2. Hook up power excitations from xSenso to analog sensors/devices if needed and if xSenso
meets the power requirement.
3. Connect a RJ-45 Ethernet cable between the unit and your Ethernet network.
4. Plug the xSenso into the power outlet by using the included power supply.
5. Power up analog input devices/sensors if they are not powered by xSenso excitation.
6. Power up device to be controlled by relay or supply power to be controlled by relay.
- User Guide 1
- Copyright & Trademark 2
- Warranty 2
- Contacts 2
- Disclaimer 2
- Revision History 2
- Table of Contents 3
- 1: Using This Guide 13 3
- 2: Introduction 15 3
- 6: Using DeviceInstaller 40 4
- 8: Network Settings 50 4
- 15: Services Settings 77 6
- 16: Security Settings 85 6
- 18: Advanced Settings 103 7
- 21: Branding the xSenso 114 8
- 19: Security in Detail 109 8
- 20: Updating Firmware 112 8
- List of Figures 10
- List of Tables 11
- 1: Using This Guide 13
- Additional Documentation 14
- 2: Introduction 15
- Applications 16
- Protocol Support 17
- Troubleshooting Capabilities 18
- Configuration Methods 18
- Addresses and Port Numbers 20
- Product Information Label 20
- 3: Installation of xSenso 22
- Hardware Components 23
- Table 3-4 Analog Input LEDs 24
- Right Side Panel 25
- Installing the xSenso 26
- Package Contents 28
- User-Supplied Items 28
- Side Panels 32
- Back Panel 32
- 6: Using DeviceInstaller 40
- Accessing Web Manager 42
- Configuration Pages 46
- HOME PAGE 46
- Live Reading Pages 46
- Web Manager Components 47
- Navigating Web Manager 48
- 8: Network Settings 50
- Network Link Settings 52
- DAQ Format 53
- To Configure DAQ Settings 54
- Analog Input 55
- Analog Output 56
- Relay Output 57
- To Configure Relay Settings 58
- 10: Chart 59
- Data Chart Configuration 60
- 11: Logging 61
- Data Logging Configuration 63
- 12: Reading 64
- Data Reading Configuration 65
- 13: Action Settings 66
- Table 13-5 FTP Put Settings 69
- Tunnel Settings 73
- Modbus Settings 75
- 15: Services Settings 77
- FTP Settings 78
- Syslog Settings 78
- HTTP Settings 79
- To Configure HTTP Settings 80
- RSS Settings 81
- SNMP Settings 82
- SMTP Settings 83
- 16: Security Settings 85
- SSH Client Known Hosts 86
- SSH Server Authorized Users 86
- SSH Client Users 87
- SSL Settings 88
- To Create a New Credential 89
- Certificate Upload Settings 90
- Trusted Authorities 91
- Filesystem Settings 92
- File Modification 93
- File Transfer 93
- Protocol Stack Settings 94
- ICMP Settings 95
- ARP Settings 95
- Diagnostics 96
- IP Sockets 97
- To Ping a Remote Host 97
- Traceroute 98
- To Perform a Traceroute 98
- To View Memory Usage 99
- Processes 99
- To View Process Information 99
- To View Thread Information 100
- System Settings 101
- Discovery and Query Port 102
- 18: Advanced Settings 103
- Basic CLI Settings 104
- SSH Settings 105
- Telnet Settings 105
- To Configure Telnet Settings 105
- XML Settings 106
- XML: Export Status 107
- To Export in XML Format 107
- XML: Import Configuration 108
- 19: Security in Detail 109
- Obtaining Certificates 110
- Self-Signed Certificates 110
- Certificate Formats 110
- Steel Belted RADIUS 111
- Free RADIUS 111
- 20: Updating Firmware 112
- 21: Branding the xSenso 114
- Name Settings Description 115
- Analog Inputs 116
- Analog Outputs 116
- Relay Ports 116
- Architecture 117
- Network Interface 117
- Management 117
- Security 117
- Software 118
- Environmental 118
- Physical Characteristics 118
- Conversion Table 120
- Scientific Calculator 120
- Appendix D: Compliance 122
© 2020, manymanuals.fr. Tous droits réservés | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels