Lantronix UDS100 Manuel d'utilisateur Page 35
- Page / 78
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
UDS10/UDS100 User Guide Configuring the UDS Using Telnet or the Serial Port
35
Disconnect Time (Inactivity Timeout)
Use Disconnect Time to set an inactivity timeout. The unit drops the connection if
there is no activity on the serial line before the set time expires. Enter time in the
following format: mm:ss, where m is the number of minutes and s is the number of
seconds. To disable the inactivity timeout, enter 00:00. Range is 0 (disabled) to 5999
seconds (99 minutes, 59 seconds). The default is 0.
Send Characters
Enter up to two characters in hexadecimal representation for the SendChar settings.
If the unit receives a character on the serial line that matches one of these
characters, it sends the character immediately, along with any awaiting characters, to
the TCP connection. This action minimizes the response time for specific protocol
characters on the serial line (for example, ETX, EOT). Setting the first SendChar to
00 disables the recognition of the characters. Alternatively, the unit can interpret two
characters as a sequence (see Pack Control on page 34).
Telnet Terminal Type
This parameter displays only if the terminal type option is enabled in Disconnect
Mode. If this option is enabled, use the terminal name for the Telnet terminal type.
Enter only one name.
If the terminal type option is enabled, the unit also reacts to the EOR (end of record)
and binary options that can be used for applications like terminal emulation to IBM
hosts.
Channel (Port) Password
This parameter displays only if the channel (port) password option is enabled in
Disconnect Mode. If the option is enabled, set a password on the serial port.
Expert Settings
Note: Change these settings using Telnet or serial connections only, not
Web Manager.
Caution: Only an expert should change these parameters. These
changes have serious consequences.
Figure 5-7. Expert Settings Options
- User Guide 1
- Copyright & Trademark 2
- Contacts 2
- Disclaimer & Revisions 3
- Contents 4
- 6: Updating Firmware 39 5
- 7: Using Monitor Mode 43 5
- Figures 6
- Purpose and Audience 8
- Chapter Summary 8
- Additional Documentation 9
- Applications 10
- Application Examples 10
- Protocol Support 12
- Additional Features 12
- Configuration Methods 12
- Product Information Label 13
- Installing the UDS 14
- Required Information 15
- DeviceInstaller 16
- Serial Port Login 17
- Accessing Web Manager 18
- Using Web Manager 20
- Using a Telnet Connection 22
- Using the Serial Port 23
- IP Address 24
- Set Gateway IP Address 24
- Netmask 24
- DHCP Naming 25
- Baudrate 26
- I/F (Interface) Mode 26
- Port Number 27
- Connect Mode 28
- Manual Connection 29
- Figure 5-6. Hostlist Option 30
- Remote IP Address 32
- Remote Port 32
- Disconnect Mode 33
- Flush Mode 33
- Pack Control 34
- Expert Settings 35
- Security Settings 36
- Factory Default Settings 38
- Exit Configuration Mode 38
- Obtaining Firmware 39
- Reloading Firmware 39
- Using TFTP 40
- Using Another Unit 41
- *** NodeSet 2.0 *** 42
- 0>DL 42
- 02049 lines loaded 42
- Using Monitor Mode Commands 44
- Collisions 45
- Diagnostics (red) 45
- Status (yellow) 45
- Problems and Error Messages 46
- Technical Support 49
- Serial Port 51
- Serial Connector Pinouts 51
- Null-Modem Cable 53
- Network Port 53
- Ethernet Connector Pinouts 54
- AutoIP 57
- ARP and Telnet 58
- Conversion Table 59
- Scientific Calculator 60
- Connect Mode Options 61
- Disconnect Mode Options 64
- Flush Mode Options 66
- Interface Mode Options 72
- Pack Control Options 73
- Declaration of Conformity 75
- Warranty 76
Produits connexes et manuels pour Matériel Lantronix UDS100
(12 pages)HP SAN Solutions manuels
Manuels d'utilisation et guides de l'utilisateur pour Cartouches d'encre HP SAN Solutions.
Nous fournissons des manuels en pdf 1 HP SAN Solutions à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels