Lantronix MPS100 Guide d'installation Page 144
- Page / 223
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Set/Define Port Commands Command Reference
12-24
Determines whether or not the port will check for the DSR signal when remote connections are made. If this
feature is enabled, remote connections to the port will not be permitted unless the DSR signal is asserted. If
this command is specified on a parallel port, the parallel status lines will be decoded to determine if the
printer is attached and on-line.
Applies To EPS1, EPS2, EPS2-100, EPS4-100, MPS1, MPS100, LPS1
Restrictions You must be the privileged user to use this command.
Parameters PortList/All
Specifies a particular port or group of ports, or all ports. Port numbers are
specified with integers between 1 and the total number of physical ports. Lists
of ports must be separated by commas. Ranges of ports must be separated by
a dash (-).
Note: In the absence of a PortList or the All parameter, the configuration will affect the
current port only.
See Also Show/Monitor/List Ports, page 12-63.
12.24.16 Set/Define Port Speed
Configures what baud rate will be used for connections to and from this port.
Applies To EPS1, EPS2, EPS2-100, EPS4-100
Restrictions You must be the privileged user to use this command.
Parameters PortList/All
Specifies a particular port or group of ports, or all ports. Port numbers are
specified with integers between 1 and the total number of physical ports. Lists
of ports must be separated by commas. Ranges of ports must be separated by
a dash (-).
Note: In the absence of a PortList or the All parameter, the configuration will affect the
current port only.
baudrate
Acceptable baud rates include 300, 600, 1200, 2400, 4800, 9600, 19200,
38400, 57600, and 115200, and 230400 (Fast Ethernet print servers only).
Examples
Local> DEFINE PORT 7-8 SPEED 9600
See Also Show/Monitor/List Ports, page 12-63; Baud Rate, page 5-2.
SET
DEFINE
PORT
PortList
ALL
SPEED baudrate
- Print Server Reference Manual 1
- Contents 3
- 1: Introduction 11
- 1.3 Terms 12
- 1.4 Server Features 12
- Introduction Server Features 13
- 1.5 How To Use This Manual 14
- 2: Concepts 15
- 2.3.1 Addressing 16
- 2.3.2 Zones 16
- 2.4 LAN Manager 17
- 2.5 LAT 18
- 2.6 TCP/IP 19
- TCP/IP Concepts 20
- 2.6.4 Reverse Telnet (RTEL) 21
- 2.6.5 LPR Support 21
- 2.7 NetWare 22
- 2.8 PostScript 23
- 2.9 Security 24
- 3: Getting Started 25
- 3.1.2 Using a Web Browser 26
- 3.3 Restricted Commands 28
- 3.4 Command Types 28
- 3.5 Abbreviating Keywords 29
- 3.6 Maintenance Issues 29
- 3.6.3 Rebooting the Server 30
- 3.8 System Passwords 32
- 3.9 Configuration Files 33
- 3.9.1 Using EZWebCon 34
- 3.9.2 Without EZWebCon 34
- 3.9.2.4 Download Sequence 36
- 4: Server Configuration 37
- Define Port 0 38
- Preferred “Albert” 38
- 4.3 LAT Server Parameters 39
- 4.4.2 NetWare Access Lists 40
- 4.5.1 IP Address 41
- 4.6 Creating Services 42
- Option Function 45
- 4.7 Security 46
- 4.7.2 IP Security Table 47
- Security Server Configuration 48
- 4.8 Event Logging 49
- 4.8.3 Event Classes 50
- 5: Ports 51
- 5.1.2 Serial Configuration 52
- 5.1.3 Virtual Ports 54
- 5.3 Security 55
- 5.3.3 Automatic Logouts 56
- 6: Using the Server 57
- 6.3 Local Server Commands 58
- 6.4 Status Displays 58
- 7: TCP/IP Host Setup 61
- 7.2 LPR Printing 62
- 7.2.1 LPR Basics 63
- % lpr -PServer_PRT /etc/hosts 64
- 5 Select LPR Port 65
- 7.2.3 LPR on AIX Hosts 66
- 7.2.3.1 Using UNIX Commands 67
- 7.2.3.2 Using SMIT 67
- 7.2.4 LPR on HP Hosts 68
- 7.2.5 LPR on SCO UNIX Hosts 69
- 7.3 Reverse Telnet (RTEL) 70
- # mkdir /tmp/rtel 71
- # cd /tmp/rtel 71
- # tar xvf / 71
- 1 Become superuser 72
- Execute the mkprt script 73
- 7.4 TCP Socket Connections 78
- 8: NetWare Host Setup 81
- 8.3 Printing 82
- 8.3.5 Configuring Rprinter 89
- 8.4 PCL 95
- 8.5 PostScript 95
- 8.6 Troubleshooting 95
- Area to Check Explanation 98
- Failure 99
- Failure code meaning Remedy 99
- 9: LAT Host Setup 101
- 9.1.2 Printing to a Service 102
- 9.1.3 Printing PostScript 103
- 9.2 Troubleshooting 104
- Local> MONITOR QUEUE 105
- $ EXIT %Xnnnnnnnn 106
- Area to check Explanation 107
- 10: AppleTalk Host Setup 109
- 10.2.2 Using LaserPrep 110
- 10.3.1.1 Error Messages 112
- 10.3.2 Host Troubleshooting 113
- 11: LAN Manager Host Setup 115
- 11.1.2 NetBIOS 117
- 12: Command Reference 121
- 12.3 Clear/Purge Commands 122
- 12.3.3 Clear/Purge Service 123
- 12.4 Cls 124
- 12.5 Crash 451 125
- 12.6 Define 125
- 12.7 Fg 125
- 12.8 Finger 125
- 12.9 Help 126
- 12.10 Initialize 127
- 12.11 List 128
- 12.12 Logout 128
- 12.13 Man 128
- 12.14 Mode 128
- 12.15 Monitor 129
- 12.16 Netstat 129
- 12.17 Ping 129
- 12.18 Purge 130
- 12.19 Remove Queue 130
- 12.20 Save 131
- 12.21 Set/Define IPsecurity 132
- 12.22 Set/Define Logging 133
- 12.23 Set Noprivileged 134
- 12.24.1 Define Port Access 135
- Local> SET NOPRIVILEGED 148
- 12.27.2 Define Protocols IP 149
- 12.29.1 Set/Define Service 173
- 12.30 Set/Define SNMP 181
- 12.31.5 Show/Monitor Queue 187
- Local> SHOW QUEUE Port 2 188
- Characteristics 189
- 12.32 Source 193
- 12.33 Stty 194
- 12.34 Su 194
- 12.35 Test Loop 195
- 12.36 Test Port 195
- 12.37 Test Service 196
- 12.38 Who 197
- 12.39 Zero Counters 197
- A: Contact Information 199
- B: Troubleshooting 201
- B.2 DHCP Troubleshooting 202
- B.3 BOOTP Troubleshooting 202
- B.4 RARP Troubleshooting 203
- B.5 Printing Problems 203
- B.6 PostScript Problems 203
- B.6.1 Bitmap Graphics 204
- C: Updating Software 205
- C.2 Reloading Software 206
- C.2.1.1 TCP/IP 207
- C.2.1.2 NetWare 207
- C.2.1.3 MOP 207
- Protocol Area to Check 208
- Glossary 209
- DHCP Glossary 210
- Glossary LAT 211
- Glossary RARP 213
- Glossary tap 215
- Thinwire Glossary 216
- Numerics 217
Produits connexes et manuels pour Serveurs d'impression Lantronix MPS100
(69 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels