Lantronix MPS100 Guide d'installation Page 207
- Page / 223
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Updating Software Reloading Software
C-7
C.2.1.1 TCP/IP
Before the Server downloads the new software, it will send DHCP, BOOTP, and/or RARP queries (all are
enabled by default). Next, the Server will attempt to download the MPS.SYS file using TFTP (Trivial File
Transfer Protocol).
Note: EZWebCon can also be used to reload software. See the Readme in the
EZWebCon directory on the distribution CD-ROM.
If a host provides DHCP, BOOTP, or RARP support, it can be used to set the Server IP address (all methods)
and loadhost information (BOOTP and RARP only). Add the Server name, IP address, hardware address,
and download path and filename to the appropriate host file (usually /etc/bootptab).
Some BOOTP and TFTP implementations require a specific directory for the MPS.SYS file; in this case the
path should not be specified in bootptab. See your host’s documentation for instructions on how to configure
the MPS.SYS file in a directory.
If BOOTP cannot be used to configure the Server IP parameters, manually configure them using the
following commands.
Figure C-2: Configuring TCP/IP Reload
The path and filename are case-sensitive and must be enclosed in quotation marks. When attempting to boot
across an IP router, you must configure the router to proxy-ARP for the Server, or use the bootgateway
feature. For more information, see Define Bootgateway in the Commands chapter.
C.2.1.2 NetWare
The MPS.SYS file should be placed in the login directory on the NetWare file server. The Server cannot
actually log into the file server (since it knows no username/password); it can only access files in the login
directory itself. On the Server, specify the file server name, filename, and path.
Figure C-3: Configuring NetWare Reload
C.2.1.3 MOP
The MPS.SYS filename is the only parameter that the Server needs to reload via MOP. Make sure the
service characteristic is enabled on the host's Ethernet circuit, copy the MPS.SYS file to the MOM$LOAD
directory, and reload the Server using the Initialize Reload command.
Note: If an error message is displayed indicating an invalid record size on the VAX
console, re-transfer the MPS.SYS file in binary mode.
Local> SET PRIVILEGED
Password> SYSTEM (not echoed)
Local>> DEFINE SERVER IPADDRESS nnn.nnn.nnn.nnn
Local>> DEFINE SERVER SOFTWARE “/tftpboot/MPS.SYS”
Local>> DEFINE SERVER LOADHOST nnn.nnn.nnn.nnn
Local>> LIST SERVER BOOT
Local>> INITIALIZE RELOAD
Local> SET PRIVILEGED
Password> SYSTEM (not echoed)
Local>> DEFINE SERVER NETWARE LOADHOST fileserver
Local>> DEFINE SERVER SOFTWARE SYS:\LOGIN\ MPS.SYS
Local>> INITIALIZE RELOAD
- Print Server Reference Manual 1
- Contents 3
- 1: Introduction 11
- 1.3 Terms 12
- 1.4 Server Features 12
- Introduction Server Features 13
- 1.5 How To Use This Manual 14
- 2: Concepts 15
- 2.3.1 Addressing 16
- 2.3.2 Zones 16
- 2.4 LAN Manager 17
- 2.5 LAT 18
- 2.6 TCP/IP 19
- TCP/IP Concepts 20
- 2.6.4 Reverse Telnet (RTEL) 21
- 2.6.5 LPR Support 21
- 2.7 NetWare 22
- 2.8 PostScript 23
- 2.9 Security 24
- 3: Getting Started 25
- 3.1.2 Using a Web Browser 26
- 3.3 Restricted Commands 28
- 3.4 Command Types 28
- 3.5 Abbreviating Keywords 29
- 3.6 Maintenance Issues 29
- 3.6.3 Rebooting the Server 30
- 3.8 System Passwords 32
- 3.9 Configuration Files 33
- 3.9.1 Using EZWebCon 34
- 3.9.2 Without EZWebCon 34
- 3.9.2.4 Download Sequence 36
- 4: Server Configuration 37
- Define Port 0 38
- Preferred “Albert” 38
- 4.3 LAT Server Parameters 39
- 4.4.2 NetWare Access Lists 40
- 4.5.1 IP Address 41
- 4.6 Creating Services 42
- Option Function 45
- 4.7 Security 46
- 4.7.2 IP Security Table 47
- Security Server Configuration 48
- 4.8 Event Logging 49
- 4.8.3 Event Classes 50
- 5: Ports 51
- 5.1.2 Serial Configuration 52
- 5.1.3 Virtual Ports 54
- 5.3 Security 55
- 5.3.3 Automatic Logouts 56
- 6: Using the Server 57
- 6.3 Local Server Commands 58
- 6.4 Status Displays 58
- 7: TCP/IP Host Setup 61
- 7.2 LPR Printing 62
- 7.2.1 LPR Basics 63
- % lpr -PServer_PRT /etc/hosts 64
- 5 Select LPR Port 65
- 7.2.3 LPR on AIX Hosts 66
- 7.2.3.1 Using UNIX Commands 67
- 7.2.3.2 Using SMIT 67
- 7.2.4 LPR on HP Hosts 68
- 7.2.5 LPR on SCO UNIX Hosts 69
- 7.3 Reverse Telnet (RTEL) 70
- # mkdir /tmp/rtel 71
- # cd /tmp/rtel 71
- # tar xvf / 71
- 1 Become superuser 72
- Execute the mkprt script 73
- 7.4 TCP Socket Connections 78
- 8: NetWare Host Setup 81
- 8.3 Printing 82
- 8.3.5 Configuring Rprinter 89
- 8.4 PCL 95
- 8.5 PostScript 95
- 8.6 Troubleshooting 95
- Area to Check Explanation 98
- Failure 99
- Failure code meaning Remedy 99
- 9: LAT Host Setup 101
- 9.1.2 Printing to a Service 102
- 9.1.3 Printing PostScript 103
- 9.2 Troubleshooting 104
- Local> MONITOR QUEUE 105
- $ EXIT %Xnnnnnnnn 106
- Area to check Explanation 107
- 10: AppleTalk Host Setup 109
- 10.2.2 Using LaserPrep 110
- 10.3.1.1 Error Messages 112
- 10.3.2 Host Troubleshooting 113
- 11: LAN Manager Host Setup 115
- 11.1.2 NetBIOS 117
- 12: Command Reference 121
- 12.3 Clear/Purge Commands 122
- 12.3.3 Clear/Purge Service 123
- 12.4 Cls 124
- 12.5 Crash 451 125
- 12.6 Define 125
- 12.7 Fg 125
- 12.8 Finger 125
- 12.9 Help 126
- 12.10 Initialize 127
- 12.11 List 128
- 12.12 Logout 128
- 12.13 Man 128
- 12.14 Mode 128
- 12.15 Monitor 129
- 12.16 Netstat 129
- 12.17 Ping 129
- 12.18 Purge 130
- 12.19 Remove Queue 130
- 12.20 Save 131
- 12.21 Set/Define IPsecurity 132
- 12.22 Set/Define Logging 133
- 12.23 Set Noprivileged 134
- 12.24.1 Define Port Access 135
- Local> SET NOPRIVILEGED 148
- 12.27.2 Define Protocols IP 149
- 12.29.1 Set/Define Service 173
- 12.30 Set/Define SNMP 181
- 12.31.5 Show/Monitor Queue 187
- Local> SHOW QUEUE Port 2 188
- Characteristics 189
- 12.32 Source 193
- 12.33 Stty 194
- 12.34 Su 194
- 12.35 Test Loop 195
- 12.36 Test Port 195
- 12.37 Test Service 196
- 12.38 Who 197
- 12.39 Zero Counters 197
- A: Contact Information 199
- B: Troubleshooting 201
- B.2 DHCP Troubleshooting 202
- B.3 BOOTP Troubleshooting 202
- B.4 RARP Troubleshooting 203
- B.5 Printing Problems 203
- B.6 PostScript Problems 203
- B.6.1 Bitmap Graphics 204
- C: Updating Software 205
- C.2 Reloading Software 206
- C.2.1.1 TCP/IP 207
- C.2.1.2 NetWare 207
- C.2.1.3 MOP 207
- Protocol Area to Check 208
- Glossary 209
- DHCP Glossary 210
- Glossary LAT 211
- Glossary RARP 213
- Glossary tap 215
- Thinwire Glossary 216
- Numerics 217
Produits connexes et manuels pour Serveurs d'impression Lantronix MPS100
(69 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels